Evaluasi Pemborosoan Mesin Bending Berbasis Pendekatan Statistical Process Control dan Overall Equipment Effectivenes
DOI:
https://doi.org/10.33379/gtech.v8i2.4037Keywords:
Defect, Kualitas, Mesin, OEE, SQCAbstract
PT. ASM is a company operating in the steel sector. In production, it is of course important to maintain machine productivity to maintain production quality performance. In the research, problems were found in the form of machine damage which resulted in production stopping. In this research, the Statistical Quality Control (SQC) method is applied as a quality management approach to control process and product quality by integrating Overall Equipment Effectiveness (OEE) and SQC. In research, there are two types of data, namely primary data and secondary data which are used as references to facilitate the problem solving process. Primary data was obtained through interviews related to the production process, machine function, and causes of defects in production, while secondary data was obtained from company data recaps related to defects in production. Based on the results of the Pareto diagram, it was found that 55% of the problems were imprecise, while 45% were caused by iron cracking during the production process. Thus, it can be concluded that product defects are mainly caused by cracks in the iron and lack of precision in the machine
References
Anggi Riska Devi, & Widya Setiafindari. (2023). Upaya Peningkatan Kualitas Produk Engine Pulley Yst Pro Menggunakan Metode Seven Tools Dan Kaizen Five M Checklist Di Pt Mitra Rekatama Mandiri. Jurnal Ilmiah Teknik Mesin, Elektro dan Komputer, 3(2), 192–204. https://doi.org/10.51903/juritek.v3i2.1743
Argarino, T., Dyanasari Sebayang, M., & Manullang, B. H. (2021). Machine Optimization of SNK HF Fabrication Plant in PT. Komatsu Indonesia with FMEA Method and Overall Equipment Effectiveness (OEE). Journal of Technomaterial Physics, 3(2), 83–88.
Dewangga, A. (2022). Analisa Pengendalian Kualitas Produksi Plywood Menggunakan Metode Seven Tools, Failure Mode And Effect Analysis (FMEA), Dan TRIZ (Studi Kasus: DI PT. ABHIRAMA KRESNA). Jurnal Teknologi dan Manajemen Industri Terapan (JTMIT), 1(3), 243–253.
Firmansyah, M. J., Nuruddin, M., Sumatra, J., 101 Randuagung, N., Kebomas, K., Gresik, K., & Timur, J. (2022). Analisis Pengendalian Kualitas Produksi Pada PT.XYZ Menggunakan Metode Seven Tools Dan FMEA. 20(1), 231–238.
Hardiatama, I., Erlangga, N. A., Yudah, P., Sidartawan, R., Arbiantara Basuki, H., & Kristianta, F. X. (2022). Analisis Perawatan Cutter Section Dredger Dengan Metode FMEA dan OEE. Jurnal Mekanova, 8(1), 62–71.
Harma, B., Farid, Susriyati, & Miliandini, E. P. (2022). Analisis Kualitas CPO Menggunakan Seven Tools dan Kaizen. Jurnal Teknologi, 13–20. https://doi.org/10.35134/jitekin.v12i1.63
Hasanudin, M. (2020). Analisis Penerapan Total Productive Maintenance Menggunakan Overall Equipment Effectiveness dan Fuzzy Fmea Pada Mesin Extruder di PT Xyz Bogor. Scientifict Journal of Industrial Engineering, 1(2), 53–58.
Kurniawan, & Salim Dahda, S. (2023). Pengendalian Kualitas Pengelasan Pada Konstruksi Mechanical Piping Dengan Metode Seven Tools. Dalam Jurnal Teknik Industri (Vol. 9, Nomor 2).
Novita, D., & Irawan, H. (2022). Analisis Pengendalian Kualitas Crumb Rubber Dengan Menggunakan Metode Seven Tools Di Pt. Batanghari Tebing Pratama. Dalam Jurnal Industri Samudra (Vol. 3, Nomor 1).
Permono, L., Salmia, S. T., Septiari, R., Program, ), & Industri, S. T. (2022). Penerapan Metode Seven Tools Dan New Seven Tools Untuk Pengendalian Kualitas Produk (Studi Kasus Pabrik Gula Kebon Agung Malang). Jurnal Mahasiswa Teknik Industri), 5(1).
Prasetyo, R., & Kusuma Bakhti, Y. (2022). Pengendalian Kualitas Produk Pakaian Anak Pada Industri Garment Dengan Metode Seven Tools. Jurnal Inkofar, 6(1), 2581–2920.
Setia Pratama, F. (2019). Jurnal SENOPATI Sustainability, Ergonomics, Optimization, and Application of Industrial Engineering Analisis Kecacatan Produk dengan Metode Seven Tools dan FTA dengan Mempertimbangkan Nilai Risiko berdasarkan Metode FMEA.
Siagian, D., Nugraha Gusniar, I., & Dirja, I. (2022). Analisis Total Productive Maintenance Dengan Metode Oee Dan Fmea Pada Mesin Extruder GW-350. Dalam Technology, Education And Mechanical Engineering (Vol. 3, Nomor 1).
Somadi, S., Priambodo, B. S., & Okarini, P. R. (2020). Evaluasi Kerusakan Barang dalam Proses Pengiriman dengan Menggunakan Metode Seven Tools. Jurnal INTECH Teknik Industri Universitas Serang Raya, 6(1), 1–11. https://doi.org/10.30656/intech.v6i1.2008
Widodo, A. (2023). Upaya Menurunkan Defect Silver Streaks Proses Injection Pada Part Lens Reflector Dengan Menggunakan Metode Seven Tools Di Pt Sanwa Engineering. Dalam Jurnal Inkofar * (Vol. 7, Nomor 1). Online.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Ahmad Syahri Muzakki, Yanuar Pandu Negoro, Hidayat Hidayat
This work is licensed under a Creative Commons Attribution 4.0 International License.
