Rancang Bangun Alat Otomatis Pengisian Fluida Cair pada Botol berbasis Arduino Uno
DOI:
https://doi.org/10.33379/gtech.v7i4.3073Keywords:
Bottle, Liquid Fluid Filling, Arduino UnoAbstract
The process of filling milk in bottles in small and medium industries is still done manually with human labor, so the operator must pay attention to the volume of milk and takes a long time. This Arduino uno-based liquid fluid filling designer is supported by the Water Flow yf-S201 sensor to read the flow of water. The purpose of this research is to find out the working system of the liquid fluid filling device in an automatic bottle based on Arduino Uno. The research conducted uses a procedural development model. The results showed that filling milk into bottles manually takes ± 340 seconds in 1 bottle filling. If using an automatic bottle filling tool based on Arduino Uno Microcontroller and Flow sensor the filling process on 1 bottle takes ± 210 seconds. This tool still has weaknesses, the weakness of this tool in filling the 5th bottle the volume drops compared to the previous bottle.
References
A.Genialdi, I. S., & M.T. (2019). Sistem Kontrol Otomatis Pengisian Cairan. 5(1), 23–34.
Aisuwarya, R., & Fatimah, N. (2019). Rancang Bangun Sistem Pencampur Minuman Jamu Otomatis Berbasis Mikrokontroler. Journal of Information Technology and Computer Engineering, 3(01), 8–17. https://doi.org/10.25077/jitce.3.01.8-17.2019
Amrullah, Karim, A., & Hardyanto, H. (2021). Alat Pengisian Air di Botol Menggunakan Arduino. Dinamika Informatika 2021, 1(2), 128–131.
Arif, I., Tobing, M. T. L., & Junaidi, Y. (2022). Perancangan Unit Pengisian Pada Mesin Pengisian Botol Otomatis Berbasis Plc. Jurnal Mesin( Mesin Elektro Sipil), 3(2), 37–44.
Hansza, R., & Haryudo, S. I. (2020). Rancang Bangun Kontrol Motor DC dengan PID Menggunakan Perintah Suara dan Monitoring Berbasis Internet of Things ( IOT ). Jurnal Teknik Elektro, 9(2), 477–485.
Lubis, P., Rasyidin, R., Frianto, H. T., Elektronika, T., Elektro, T., & Medan, P. N. (2022). Rancang Bangun Water Treatment Sistem sebagai Pengolahan Air Bersih Berbasis Program Logic Controler (PLC). Konferensi Nasional Sosial Dan Engineering Politeknik Negeri Medan, 823–829.
Munandar, A., Veronika, N. D. M., Abdulllah, D., & Sahputra, E. (2023). Miniature Design of Liquid Filling Machine Automatically Using ESP32 Based IOT ( Internet of Things ) Perancangan Miniatur Mesin Pengisi Cairan Otomatis Menggunakan ESP32 Berbasis IOT ( Internet of Things ). KOMITEK, 3(1), 69–78.
Ramadhan, B. K. A., Syafrudin, M., & Nur, M. (2021). Mesin Filling Dan Capping Botol Madu Hutan Dengan Menggunakan Flowmeter Sebagai Pengatur Volume. Jurnal Techno Bahari, 8(1), 24–29.
Rumalutur, S., & Allo, S. L. (2019). Sistem Kontrol Otomatis Pengisian Cairan Dan Penutup Botol Menggunakan Arduino Uno Rev 1.3. Electro Luceat, 5(1), 23–34. https://doi.org/10.32531/jelekn.v5i1.129
Selviana, D., Rakhman, A., & Rais. (2021). Rancang Bangun Website Monitoring Pengisian Botol Susu Otomatis pada Industri Kecil Menengah. Doctoral Dissertation, Politeknik Harapan Bersama Tegal.
Setiawan, H. A. (2019). Rancang Bangun Sistem Kontrol Pengisian Air Minum Dalam Kemasan Menggunakan Arduino Uno Dengan Sensor Load Cell. Jurnal Teknik Elektro, 08(03), 579–585.
Trisetiyanto, A. N. (2020). Rancang Bangun Alat Penyemprot Disenfektan Otomatis Untuk Mencegah Penyebaran Virus Corona. Joined Journal (Journal of Informatics Education), 3(1), 45–51.
Ulum, M., Haryanto, & Wahyudi. (2020). Penentuan Pengisian Volume Botol Menggunakan Pid (Propotional Integral Derivative) Berbasis Raspberry Pi. Seminar Nasional Fortei Regional 7, 3(1), 285–29
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Indra Riyanto, Miftakhul Maulidina, Kartika Rahayu Tri Prasetyo Sari, M. Dewi Manikta Puspitasari
This work is licensed under a Creative Commons Attribution 4.0 International License.
