A DESIGN AND CONSTRUCTION OF A DRONE FLAMETHROWER, A KITE BURNING TOOL ON AN ARDUINO BASED TRANSMISSION LINE
DOI:
https://doi.org/10.33379/gtech.v8i1.3747Keywords:
Drone, Flametrhrower, KitesAbstract
Flying kites around transmission lines is prohibited. This is stated in the Minister of Energy and Mineral Resources' regulation Number 02 of 2019 concerning Free Space and Minimum Clearance on Electric Network Air Lines. To clean a kite using the conventional method requires the maintenance team to use a trash cleaning stick that is stuck in the conductor network or certain other methods. This tool is useful for burning kite waste that is stuck in transmission lines which is controlled using two controllers, namely transmitter and receiver with Arduino as the control center. This research uses quantitative methods of the Research and Development (R & D) type.
The results obtained from this research show that based on test results, up to a distance of 20 meters this flamethrower drone can send and receive commands as desired and successfully burn kites on the electric power system network with a height of 17 meters and the average burning time for Burns 1 kite for 13 seconds. So it can be concluded that the design of the flamethrower drone can run well.
References
(Persero), P. P. (2020). Pedoman Pemeliharaan dan Asesmen Kondisi Peralatan Sistem Tenaga. 120.
Aminullah, T. (2020). Rancang Bangun Drone Pembersih Sampah Menggunakan Arduino Uno Sebagai Pengendali Utama. i–38.
Ariyanti, R. F. (2017). Identifikasi Penyebab Susut Energi Listrik Pt Pln ( Persero ) Area Semarang Menggunakan Metode Failure Mode & Effect Analysis ( Fmea ).
Gusti Made Ngurah Desnanjaya, I., & Dwi Alfian, M. (2020). Pengiriman Data Nrf24L01+ Dengan Kondisi Line of Sight Dan Non Line of Sight. Jurnal RESISTOR (Rekayasa Sistem Komputer), 3(2), 128–139. https://s.id/jurnalresistor
Hadisantoso, F. S. (2016). Analisa Penurunan Tegangan ( Voltage Drop ) dan Rugi-rugi ( Losses ) Penyulang Menggunakan ETAP di Gardu Induk Bandung Selatan. 1(2).
Hafiz, D. M. Al, Dwijayanti, S., Sandi, D., Rahmatullah, M. S., & Capelo, F. (2023). Desain dan Implementasi Robot Pembersih Layang-Layang Otomatis pada Kabel Listrik. Jurnal Teknologi Rekayasa, 8(1), 117–122. https://doi.org/10.31544/jtera.v8.i1.2023.117-122
Indra Wiguna, I. G. N., Dyana Arjana, I. G., & Indra P, T. G. (2019). Analisa Rekonfigurasi Jaringan Distribusi 20 kV Pada Penyulang Berawa Untuk Menurunkan Losses dan Drop Tegangan Penyaluran Tenaga Listrik. Jurnal SPEKTRUM, 6(2), 67. https://doi.org/10.24843/spektrum.2019.v06.i02.p10
Iskandar, I. (2021). Rancang Bangun Prototype Robot Pemungut Sampah Berbasis Arduino Mega. Nuevos Sistemas de Comunicación e Información, 15290401011, 2013–2015.
Katu, M. (2021). Robot Kapal Pemungut Sampah di Sungai Menggunakan Mikrokontroler Arduino Uno dengan Pengendali Jarak Jauh (Garbage Collecting Ship Robot on the River Using Arduino Uno Microcontroller with Remote Control).
Suprianto. (2018). Analisa Tegangan Jatuh pada Jaringan Distribusi 20 kV PT.PLN Area Rantau Prapat Rayon Aek Kota Batu. Journal of Electrical Technology, 3(2), 64–72.
Widiasari, C., & Este, R. S. A. D. (2020). Rancang Bangun Drone Quadcopter Tanpa Awak Penyiram Pupuk Tanaman. Jurnal ELEMENTER, 6(2), 81–89. https://jurnal.pcr.ac.id/index.php/elementer
Wijaya, A., & Juliadi, D. (2021). Rancang Bangun Robot Pembersih Lantai Menggunakan Arduino Nano Dengan Sistem Pengendali Berbasis Android. Pseudocode, 8(2), 98–107. https://doi.org/10.33369/pseudocode.8.2.98-107
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Taryo Taryo, Rindi Wulandari, Muhamad Riyad Ariwibowo, M. Angga Priyanto
This work is licensed under a Creative Commons Attribution 4.0 International License.
